- 25 Feb, 2014 21 commits
-
-
git://git.denx.de/u-boot-mpc85xxTom Rini authored
With this, fixup a trivial build error of get_effective_memsize needing to be updated in the new board/freescale/p1010rdb/spl.c Signed-off-by:
Tom Rini <trini@ti.com>
-
Masahiro Yamada authored
arch/arm/cpu/armv7/omap-common/config.mk is never included because "omap-common" is not SoC name. If we want to add OMAP-specific compiler flags, they must be added to omap3/config.mk, omap4/config.mk, omap5/config.mk. Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com>
-
Masahiro Yamada authored
Same as the previous commit. Move sanity check to prepare1 target to avoid nasty troubles. Before this commit, LDSCRIPT existence was not checked when it was specified by CONFIG_SYS_LDSCRIPT. Now LDSCRIPT existence is checked for all boards. $(wildcard $(LDSCRIPT)) must point to the linker scripts with absolute path. Otherwise, make will terminate with a false error on out-of-tree build. Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Masahiro Yamada authored
Before this commit, make terminated with an error where is shouldn't under some condition. This bug happened when we built a board unsupporting generic board right after building with generic board. For example, the following sequence failed. (harmony uses generic board but microblaze-generic does not support it) $ make harmony_config Configuring for harmony board... $ make CROSS_COMPILE=arm-linux-gnueabi- [ Build succeed ] $ make microblaze-generic_config Configuring for microblaze-generic board... $ make CROSS_COMPILE=microblaze-linux- Makefile:488: *** Your architecture does not support generic board. Please undefined CONFIG_SYS_GENERIC_BOARD in your board config file. Stop. We had to do "make clean" before building the microblaze board. This commit fixes this unconvenience. Move generic board sanity check to "prepare1" target, which is run after generation of include/autoconf.mk. Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Masahiro Yamada authored
Commit 6ab6b2af deleted ./u-boot.dtb because it was a copy of dts/dt.dtb. But Simon suggested to keep u-boot.dtb at the top directory because it is a build output. After discussions, we agreed on revival of ./u-boot.dtb. Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@ti.com> Acked-by:
Simon Glass <sjg@chromium.org>
-
Masahiro Yamada authored
"help" target has been copied from Linux 3.13 and adjusted for U-Boot. Unlike Linux, cleaning is done on 4 levels: clean, clobber, mrproper, distclean. Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Masahiro Yamada authored
Import build rules of single targets from Linux 3.13. Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Masahiro Yamada authored
This commit avoids generating ./SPL twice. - Fist time descending to spl/ - Second time as a prerequisite of u-boot-with-spl.imx, u-boot-with-nand-spl.imx. Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Masahiro Yamada authored
Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Masahiro Yamada authored
Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Masahiro Yamada authored
Move sandbox-specific link rule to arch/sandbox/config.mk. Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Masahiro Yamada authored
Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Masahiro Yamada authored
Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Masahiro Yamada authored
Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Masahiro Yamada authored
Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Masahiro Yamada authored
Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by:
Simon Glass <sjg@chromium.org>
-
Masahiro Yamada authored
Rename OBJCFLAGS to OBJCOPYFLAGS beforehand to use "cmd_objcopy" in scripts/Makefile.lib in an upcoming commit. Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Masahiro Yamada authored
Generate include/generated/generic-asm-offsets.h and include/generated/asm-offsets.h in ./Kbuild. This commit also changes the include guard. Before this commit, __ASM_OFFSETS_H__ was used for both of them. So we could not include generic-asm-offsets.h and asm-offsets.h at the same time. This commit renames the include guard of the former to __GENERIC_ASM_OFFSETS_H__. Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Masahiro Yamada authored
This commit moves include/generated/{generic-asm-offsets.h, asm-offsets.h} from "depend" targets to "prepare" targets and deletes "depend" targets. Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Masahiro Yamada authored
- Generate include/generated/{timestamp.h, version.h} more simply by using filechk rule. - Add $(UBOOTRELEASE) variable and re-write u-boot.imx rule more simply. - Rename U_BOOT_VERSION in Makefile to UBOOTVERSION Before this commit, the same variable name, "U_BOOT_VERSION" was used for two different strings. One of them was defined in Makefile. It takes the form like "2014.01-rc1" and used in makefiles and script files. The other is defined in include/generated/version.h It takes the form like "U-Boot 2014.01-rc1-00010-gbe6d4266 -dirty" and used in C and Aseembler. It is confusing when grepping the source tree. So, this commit renames the former to UBOOTVERSION. Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Masahiro Yamada authored
If -fstack-usage option is given to crosstools that do not support it, gcc displays a warning message but still exits with status 0. This means we can not rely on $(call cc-option,...) to detect if -fstack-usage option is supported or not. Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
- 24 Feb, 2014 15 commits
-
-
Nikhil Badola authored
Use first four characters for phy_type comparison. Strcmp() should not be used to check the phy_type string which maybe parsed by hwconfig_subarg(). Hwconfig_subarg() returns part of hwconfig string starting from phy_type value till the end of the string. Since phy_type could be either "utmi" or "ulpi", strncmp() should be used so that a comparison of "utmi;fsl_ddr:bank_intlv=auto" with "utmi" will succeed. Signed-off-by:
Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by:
Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by:
York Sun <yorksun@freescale.com>
-
Haijun.Zhang authored
u-boot binary size for Freescale mpc8536DS platforms is 512KB. This has been reached to upper limit of the platforms and causig linker error. So increase the u-boot binary size to 768KB. Signed-off-by:
Haijun Zhang <Haijun.Zhang@freescale.com> Reviewed-by:
York Sun <yorksun@freescale.com>
-
Zhao Qiang authored
Function "genphy_parse_link()" used "if (mii_reg & BMSR_ANEGCAPABLE)" before while "if (phydev->supported & SUPPORTED_Autoneg)" now. So assign "phydev->supported" to "phydev->drv->features" for ar8031/8033 to enable autonegotiation. Signed-off-by:
Zhao Qiang <B45475@freescale.com> Reviewed-by:
York Sun <yorksun@freescale.com>
-
Ying Zhang authored
In the previous patches, we introduced the SPL/TPL fraamework. For SD/SPI flash booting way, we introduce the SPL to enable a loader stub. The SPL was loaded by the code from the internal on-chip ROM. The SPL initializes the DDR according to the SPD and loads the final uboot image into DDR, then jump to the DDR to begin execution. For NAND booting way, the nand SPL has size limitation on some board(e.g. P1010RDB), it can not be more than 8KB, we can call it "minimal SPL", So the dynamic DDR driver doesn't fit into this minimum SPL. We added the TPL that is loaded by the the minimal SPL. The TPL initializes the DDR according to the SPD and loads the final uboot image into DDR,then jump to the DDR to begin execution. This patch enabled SPL/TPL for P1010RDB to support starting from NAND/SD/SPI flash with SPL framework and initializing the DDR according to SPD in the SPL/TPL. Because the minimal SPL load the TPL to L2 SRAM and the jump to the L2 SRAM to execute, so the section .resetvec is no longer needed. Signed-off-by:
Ying Zhang <b40530@freescale.com> Reviewed-by:
York Sun <yorksun@freescale.com>
-
Ying Zhang authored
There was no enough memory for malloc in SPL booting from spi flash, so relayout the memory in SPL: reduce the memory for global data from 16K Bytes to 4K Bytes, save the space for malloc. Signed-off-by:
Ying Zhang <b40530@freescale.com> Reviewed-by:
York Sun <yorksun@freescale.com>
-
Ying Zhang authored
There was no enough stack in SPL, so the buffer needed in SPL is to malloc from memory pool and to repalce the temporary variable. Signed-off-by:
Ying Zhang <b40530@freescale.com> Reviewed-by:
York Sun <yorksun@freescale.com>
-
Ying Zhang authored
1. The SPL's length of SDCARD boot has not enough,expand the SPL's length to 128K. 2. deleted unused symbol: CONFIG_SYS_RUN_INDDR Signed-off-by:
Ying Zhang <b40530@freescale.com> Reviewed-by:
York Sun <yorksun@freescale.com>
-
Shengzhou Liu authored
T2081 QDS is a high-performance computing evaluation, development and test platform supporting the T2081 QorIQ Power Architecture processor. T2081QDS board Overview ----------------------- - T2081 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz - 2MB shared L2 and 512KB L3 CoreNet platform cache (CPC) - CoreNet fabric supporting coherent and noncoherent transactions with prioritization and bandwidth allocation - 32-/64-bit DDR3/DDR3LP SDRAM memory controller with ECC and interleaving - Ethernet interfaces: - Two on-board 10M/100M/1G bps RGMII ports - Two 10Gbps XFI with on-board SFP+ cage - 1Gbps/2.5Gbps SGMII Riser card - 10Gbps XAUI Riser card - Accelerator: - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC - SerDes: - 8 lanes up to 10.3125GHz - Supports SGMII, HiGig, XFI, XAUI and Aurora debug, - IFC: - 512MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA - eSPI: - Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040) - USB: - Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB) - PCIe: - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV) - eSDHC: - Supports various SD/SDHC/SDXC/eMMC devices with adapter cards and voltage translators - I2C: - Four I2C controllers. - UART: - Dual 4-pins UART serial ports Signed-off-by:
Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by:
York Sun <yorksun@freescale.com>
-
Shengzhou Liu authored
- fix serdes definition for t2081. - fix clock speed for t2081. - update ids, as CONFIG_FSL_SATA_V2 is needed only for t2080, T2081 has no SATA. Signed-off-by:
Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by:
York Sun <yorksun@freescale.com>
-
Fabio Estevam authored
Run "tools/reformat.py -i -d '-' -s 8 <boards.cfg >boards0.cfg && mv boards0.cfg boards.cfg" in order to keep arc entries sorted. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com>
-
Masahiro Yamada authored
Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Stephen Warren <swarren@nvidia.com> Cc: Rajeshwari Birje <rajeshwari.s@samsung.com> Cc: Inderpal Singh <inderpal.singh@linaro.org>
-
Masahiro Yamada authored
HOSTCFLAGS_autoconf.mk.dep was added by commit 422322f2 but it has never been used. Cc: Vadim Bendebury <vbendeb@chromium.org> Cc: Simon Glass <sjg@chromium.org> Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Łukasz Majewski authored
Lack of this check resulted in a data abort when CPU tried to execute the following command (without further mandatory input): 'pmic MAX77686_PMIC'. Only the 'pmic list' command requires one passed parameter. Other require at least two valid parameters for correct operation. Signed-off-by:
Lukasz Majewski <l.majewski@samsung.com>
-
Masahiro Yamada authored
Commit 6825a95b (kbuild: use Linux Kernel build scripts) changed the behavior of linkage when USE_PRIAVATE_LIBGCC is defined as "yes". (It dropped arch/arm/lib/eabi_compat.o from the target library.) Affected boards are all Tegra boards. This commit gets back the same behavior as before Kbuild series. Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Tom Rini <trini@ti.com>
-
Hector Palacios authored
The calloc() call was allocating space for the sizeof the struct pointer rather than for the struct contents. Besides, since this buffer is passed to mmc for writing and some platforms may use cache, the legacy_mbr struct should be cache-aligned. Signed-off-by:
Hector Palacios <hector.palacios@digi.com> Tested-by:
Lukasz Majewski <l.majewski@samsung.com>
-
- 21 Feb, 2014 4 commits
-
-
Karicheri, Muralidharan authored
Fix the following checkpatch warning:- WARNING: externs should be avoided in .c files Signed-off-by:
Murali Karicheri <m-karicheri2@ti.com>
-
Heiko Schocher authored
compare two U-Boot Environment variables with itest.s, example: => print tmp ver tmp=U-Boot 2013.10-g75e ver=U-Boot 2013.10-g75eb4bc (Jan 21 2014 - 10:35:39)MPC83XX => print check_ub_ver check_ub_ver=if itest.s \${tmp} == \${ver}; then echo equal; else echo diff ;fi => run check_ub_ver diff => setenv tmp U-Boot 2013.10-g75eb4bc (Jan 21 2014 - 10:35:39)MPC83XX => print tmp ver tmp=U-Boot 2013.10-g75eb4bc (Jan 21 2014 - 10:35:39)MPC83XX ver=U-Boot 2013.10-g75eb4bc (Jan 21 2014 - 10:35:39)MPC83XX => run check_ub_ver equal Signed-off-by:
Heiko Schocher <hs@denx.de>
-
Heiko Schocher authored
check with this ubi command, if a UBI volume with "volumename" exists in current ubi device. Signed-off-by:
Heiko Schocher <hs@denx.de>
-
Masahiro Yamada authored
There are some entries which produce the same binaries: - ep8248E is equivalent to ep8248 - MPC8360ERDK_66 is equivalent to MPC8360ERDK - Adder87x/AdderUSB is equivalent to Adder - EVB64260_750CX is equivalent to EVB64260 I also notice - Lite5200 is equivalent to icecube_5200 - Lite5200_LOWBOOT is equivalent to icecube_5200_LOWBOOT - Lite5200_LOWBOOT08 is equivalent to icecube_5200_LOWBOOT08 But I am keeping them. (Wolfgang suggested to do so because Lite5200* are referenced in misc documents.) Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-