GitLab

Operating channel is always set even without an STA connected. Remove
channel list filtering based on that.

Channel list is filtered in the p2p_connect and p2p_invite path based
on force_freq which is essentially the operating channel for STA

This patch helps fix WifiDirect b/w two android devices for SCC while at
the same time keeping channel compliance with WFD dongle

Bug: 7232932
Change-Id: Ie9524f9e45b6f997959c3359a81b05f63b576045

- P2P: Show own channel list in debug log
- P2P: Allow peer to propose channel in invitation process
- P2P: Clear sta_scan_pending on group removal
- P2P: Fix ignoring of PD Response due to dialog token mismatch

BUG: 7226065, 7231289

Change-Id: Iacb0f85d80f63bcdf311ccc0d29d0c282a0c0576
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>

- Remove unused function warning in WPS-NFC case
- P2P: Fix p2p_ctrl_invite_persistent to parse peer parameter
- hostapd: Fix CONFIG_INTERWORKING=y build without CONFIG_HS20=y
- hostapd: Fix WDS VLAN bridge handling
- hostapd: Send EAPOL frames from the VO queue if WMM is active
- P2P: Remove channel 14 from supported P2P channels
- hostapd: Clear WLAN_STA_ASSOC_REQ_OK if sending the assoc response failed
- hostapd: Add check for the wds sta flag before creating 4addr VLANs
- nl80211: Use the monitor interface if socket tx status is not supported
- wpa_supplicant: Set state to DISCONNECTED on AP creation errors
- P2P: Fix p2p_group_idle in no-group-interface P2P client case
- P2P: Fix PSK configuration for GO network
- Print control interface commands in easier format
- Add debug print for no enabled networks case
- P2P: Add more debug prints for GO start routines
- P2P: Fix pending sta scan processing for concurrent operation cases

BUG: 6940646
Change-Id: I1b1c54a08c61ec4af2bfd2274afc93501004eea2
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>

Change-Id: I847b63428b47016cf9a9a0b090636e1d5b9d28b8

- Force operating channel as the only channel in channel list attribute for go negotiation
and persistence
- Force an operating channel in go negotiation response even if the GO indicates a different
in negotiation request
- Fix a bug with updating peer operating channel based on GO negotiation confirm

Bug: 7217600
Change-Id: I6da0dc1a49c1d99ae97dcab8ee9899e07a80a6cb

If a connection operation is started on an interface based on scan
results, other virtual interfaces should not be information about the
results to avoid potential concurrent operations during the association
steps. Since the sibling notification of scan results received was added
as an optimization, skipping it for this type of cases is the simplest
way of avoiding unnecessary concurrent operations.

Change-Id: I145b4237074a97cc75fd68933fff7ed99b850630
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>

This makes sure that the interrupted station mode scan can be completed
after the P2P operations have had their chance of using the radio.

Signed-hostap: Jouni Malinen <j@w1.fi>

Driver could reject the new scan based on any virtual interface
running a concurrent scan. As such, mark the pending scan callback
for P2P based on any interfaces instead of just the one used for
the p2p_scan operation.

Signed-hostap: Jouni Malinen <j@w1.fi>

Since we have a global P2P module, the flag to trigger scan completion
events to it needs to be in similar context. The previous design
maintained this separately for each virtual interface and if P2P module
did not run its scan operation on the virtual interface that completed
the scan, P2P module would not be allowed to restart operations
properly.

Change-Id: I1b5a55c03aede15bbe0ac70dcbe0011a90f69b20
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>

Change-Id: Ieea8843c0fcb063dbb1df56e5cdf3fbdd0590cd4
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>

commit 762b99db7a76803d1ad274e87caa6fe870d47441
Author: Jouni Malinen <j@w1.fi>
Date:   Mon Sep 10 12:33:29 2012 +0200

    Fix last_scan_res update existing BSS entry is update

Change-Id: I03f933bf6d7f7e36b0f8ac410fbc37990f127c18
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>

Change-Id: I46cb3d2f17a45bf0ff62697040602334b818d805
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>

Change-Id: Ib2e811513be7b05178e310040f7cae14cb425421
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>

Change-Id: I733b23c2b7a24cfa96fe6593adbcbeb7d0798002
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>

Change-Id: Ic5cdb4df220834faf9e7da5cc1cc0a4191e6abd1

BUG: b/7137954

Change-Id: I64ef8dbb51c354b4cdebe490ffcd2cec07995939
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>

This reverts commit 5d03c02c

Change-Id: I27492d70600007f6a1230b166e03c7a47ad63788

BUG: b/7137954

Change-Id: I64ef8dbb51c354b4cdebe490ffcd2cec07995939
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>

commit 44256451130c4766e4a019162de17d0734444ee9
Author: Arik Nemtsov <arik@wizery.com>
Date:   Fri Sep 7 00:22:40 2012 +0300

    AP: Configure basic rates from iface and not conf

Skipped patches:
20ed5e40ba95440a1946cf2dffad3047fb620582
cf8baca6a5719f4f3257631e03317affee015417
a297201df15656dbb0f37e90f3410d9e8102c6fd
620c783753bddd37988269314862dc7e4a62f700

Change-Id: I857aa80af6d1a21b61f7c03a085e7dfc6066d61a
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>

Change-Id: If25804d41e7ea1d028a30c180290d8de547f43e8

The conf doesn't contain any basic rates in some cases. Most notably,
when starting a P2P GO in 5 GHz. Use the iface rates which are
initialized in hostapd_prepare_rates() to the conf rates or set to
default values if no conf values exist. This fixes a bug introduced in
commit e5693c4775bae65faa960f80889f98b0a6cb2e1c.

Signed-hostap: Arik Nemtsov <arik@wizery.com>

The wpa_s->current_ssid pointer may get cleared, e.g., when
disconnected. Commit 30ee769235f3170d9bf6b62c11c6e018e97deb84 made
wpas_p2p_group_delete() exit early before removing a P2P interface in
this type of case. That can cause number of issues from p2p_group_remove
command failing to busy loop when terminating wpa_supplicant if there is
a P2P group interface in client mode and that interface happens to be in
disconnected state. Fix these issues by allowing wpas_p2p_group_delete()
remove the P2P group interface regardless of whether wpa_s->currnt_ssid
is set.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>

The freq and ht40 parameters can now be used with the p2p_invite
command when reinvoking a persistent group as the GO.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>

Commit 0d30cc240fa36905b034dc9676f9d8da0ac18e56 forced
wpa_s->current_ssid to be cleared in wpa_supplicant_mark_disassoc()
which gets called from wpa_supplicant_event_disassoc(). This broke SME
disassoc-while-authenticating workaround for cfg80211. Fix this by
restoring wpa_s->current_ssid in case SME authentication is in progress.

Signed-hostap: Jouni Malinen <j@w1.fi>